Best Bike Phone Mount for E-Bikes: 6 Holders Compared
IBy Ilias · Updated October 10, 2026 · Listings checked on Amazon.com
Affiliate links: if you buy through our links, we earn a commission at no extra cost to you. It does not affect our picks.
In short
The best bike phone mount for most e-bike riders is the Lamicall BM02. It locks the clip with a red switch, fits phones from 4.7 to 6.8 in on bars from 15 to 40 mm, and carries a 4.6 rating from 69,002 shoppers. If your phone is bigger, the JOYROOM takes up to 7 in.
Check priceOur pick: Lamicall BM02 Bike Phone Mount
OUR PICK
Lamicall BM02 Bike Phone Mount
Best for: E-bike and scooter riders who want an inexpensive, lockable handlebar mount for GPS and calls.
A lockable, tool-free clip with the widest bar range here and the most reviews. Check that your phone in its case stays under 6.8 in and 0.59 in thick.
The clip holds phones from 4.7 to 6.8 in, up to 0.59 in thick including the case.
It fits handlebars from 0.59 to 1.57 in (15-40 mm), with 4 extra silicone pads to adjust the fit.
A red switch on the back locks the clip so the phone does not fall out on bumpy roads.
Specs taken from the product listings on October 10, 2026. –: not listed by the manufacturer.
The models in detail
This page is for e-bike riders who want their phone on the handlebar for navigation, calls or a ride app. We compared six handlebar phone holders from Amazon.com product listings checked on October tenth, 2026, looking at phone size, bar diameter, rotation and how the phone is held and released. We did not ride with these mounts; everything below is taken from the product pages.
1 · Our pick
Lamicall BM02 Bike Phone Mount
Phone mount4,6/5 from 69002 Amazon customer ratings (as of October 10, 2026)
The BM02 balances fit and grip better than any other mount on this page. Its clip takes phones from 4.7 to 6.8 in, up to 0.59 in (15 mm) thick with the case, and the screw clamp fits handlebars from 0.59 to 1.57 in (15-40 mm), the widest range here, with 4 extra silicone pads to adjust the fit. That range matters on e-bikes, where oversized bars and a crowded cockpit are common. A red switch on the back locks the clip so the phone stays put on bumpy roads, and the phone can sit vertically or horizontally. Its 4.6 rating from 69,002 reviews is the strongest on the page. The limits: larger phones will not fit, the brand warns that pulling the lower arms can jam the gears, and the listing does not name the body material. There is no full 360-degree ball joint like on the BP07.
Pros, cons and specs
Pros
The clip holds phones from 4.7 to 6.8 in, up to 0.59 in thick including the case.
It fits handlebars from 0.59 to 1.57 in (15-40 mm), with 4 extra silicone pads to adjust the fit.
A red switch on the back locks the clip so the phone does not fall out on bumpy roads.
Installation needs no tools, and the phone can sit vertically or horizontally.
Cons
Phones larger than 6.8 in or thicker than 0.59 in with the case will not fit.
The brand warns that pulling the lower arms can jam the internal gears; only the top arm should be opened.
The listing does not state the material of the mount body.
Best for: E-bike and scooter riders who want an inexpensive, lockable handlebar mount for GPS and calls.
Skip it if your phone is larger than 6.8 in or you prefer a quick-release mount system.
The Roam net takes a different approach: a stretchy silicone net wraps the phone, and three net sizes come in the box. The listing gives a fit of 4.6 to 7 in long and up to 3.6 in wide, though the brand's own table lists a 6.7 in height limit, so treat 7 in as the upper edge. The clamp fits 7/8 to 1.25 in bars without tools, which is narrower than the Lamicall range, so measure your e-bike's bar first. A ball socket lets you switch between portrait and landscape and, per the listing, dampens vibration. Buttons, camera and charging port stay open, handy if you charge from the e-bike's USB port. Downsides: the phone is exposed to rain, there is no cover, and you stretch the net on every ride. It has a 4.3 rating from 63,280 reviews.
Pros, cons and specs
Pros
Stretchy silicone net holds phones 4.6 to 7 in long and up to 3.6 in wide; three net sizes included.
Handlebar clamp fits 7/8 to 1.25 in bars, tool-free.
Ball socket allows portrait or landscape viewing and dampens vibration, per the listing.
Leaves buttons, camera, and charging port accessible.
Cons
The net leaves the phone exposed to rain; there is no case or cover.
No quick-release: the phone is stretched into the net each time.
The brand's table lists a 6.7 in height limit, slightly below the 7 in in the bullets.
Best for: Riders who want a cheap, universal phone holder for navigation on any handlebar.
Skip it if you have a phone larger than 7 in or want a locking quick-release mount.
The BP07 is Lamicall's quick-adjust model. A push-button handlebar clip clamps 15-40 mm bars without tools, so moving it from your e-bike to a second bike takes seconds. The phone side takes the same 4.7 to 6.8 in phones up to 0.59 in thick as the BM02, held by a metal safety lock and silicone pads on the four corners and back. A 360-degree ball joint gives more angle options than the BM02's fixed portrait or landscape choice. The listing is candid about fit: the clamp maxes out at 6.61 x 3.11 in, so Galaxy S25 Ultra and S24 Ultra phones in a case may not fit. The brand's own table says the clamp can block the camera, and there is no vibration damper, which matters on a fast e-bike over rough pavement. It holds a 4.6 rating from 20,912 reviews.
Pros, cons and specs
Pros
A push-button handlebar clip adjusts to the bar without tools.
A metal security lock on the back keeps the phone clamp closed.
Silicone pads on the four corners and back protect the phone from scratches and slipping.
Fits phones from 4.7 to 6.8 in and up to 0.59 in thick, on 15-40 mm handlebars.
Cons
The listing warns that Galaxy S25 Ultra and S24 Ultra with a case may not fit (clamp max 6.61 x 3.11 in).
The brand's own table indicates the clamp can block the camera.
No vibration damper, which matters on fast or rough rides.
Best for: Cyclists who switch the mount between bikes often and want a tool-free clamp.
Skip it if your phone is an Ultra-size model in a case or you need a vibration damper.
JOYROOM's auto-lock mount clamps the phone with four arms in one click and releases it when you press both sides, the quickest one-hand action on this page. An extra lock switch double-locks the phone on bumpy roads. It takes phones from 4.7 to 7 in and up to 0.71 in thick with a case, more room than the Lamicall mounts, and closed foldables without a case. A reinforced ball joint with a silicone-filled thread holds the angle. Two caveats matter for e-bikes. The bar range of 0.7 to 1.34 in is narrower than the 15-40 mm Lamicall clamps, so check your handlebar diameter. And the 100 mph anti-shake claim in the title is the brand's own, written with motorcycles in mind. The listing gives no body material, and the brand table says it blocks the camera. It has a 4.5 rating from 16,901 reviews.
Pros, cons and specs
Pros
Four arms lock the phone automatically with one click and release with a two-side press.
An extra high-speed lock switch double-locks the phone on bumpy roads.
Phones from 4.7 to 7 in and up to 0.71 in thick fit, including foldables when closed and without a case.
A reinforced ball joint with a silicone-filled thread holds the angle.
Cons
The handlebar range (0.7-1.34 in) is narrower than some competitors.
The 100 mph anti-shake claim in the title is the brand's own, and the listing gives no material for the mount body.
The brand table indicates it blocks the camera.
Best for: Riders who want a quick one-hand dock for large phones on e-bikes or motorcycles.
Skip it if your handlebar is thicker than 1.34 in.
TruActive holds the phone with four corner grips over a non-slip anti-vibration pad, and fits screens from 4 to 7 inches up to 18 mm thick, the most generous case allowance after the JOYROOM. The clamp fits 0.55 to 1.26 in (15-32 mm) bars without tools, so thin bars and stems are fine, but an oversized e-bike handlebar may be too thick; measure where you plan to mount it. A ball joint lets you set any viewing angle, and the box includes six colored bands, plus a lifetime warranty per the listing. What is missing: the listing does not give the material or any quick-release details, and corner-grip mounts can be fiddly with cases near that 18 mm maximum. Compared with the Lamicall BM02, you trade the lockable clip for more case room. It holds a 4.5 rating from 15,190 reviews.
Pros, cons and specs
Pros
Four-corner grips and a non-slip anti-vibration pad hold phones with 4 to 7-inch screens.
Fits 0.55 to 1.26 in (15-32 mm) handlebars without tools.
Ball joint allows any viewing angle.
Six colored bands included and a lifetime warranty, per the listing.
Cons
Corner-grip mounts can be fiddly with very thick cases (18 mm maximum).
Material and quick-release details are not specified.
Best for: E-bike and scooter riders who want a stable universal phone mount for navigation.
Skip it if you want a magnetic or case-based quick-release system.
This unbranded holder is the simplest design here: rubberized grips and a silicone band hold phones and GPS units up to 3.7 in wide, and three spare bands in different colors come in the box. The clamp tightens with two metal bolts, which the listing says prevents slipping, and the mount rotates 360 degrees for portrait or landscape. The body is metal and plastic. The gaps are significant for an e-bike. There is no brand or model name, the handlebar diameter range is not given, so you cannot confirm it fits your bar, and there is no lock or quick release, only grips and a band. Compared with the Lamicall BM02 or the JOYROOM, you lose any locking feature. It has a 4.3 rating from 14,988 reviews, and it makes sense as a spare or for slow, smooth rides.
Pros, cons and specs
Pros
Holds phones and GPS units up to 3.7 in wide with rubberized grips and a silicone band.
Two metal bolts secure the clamp to prevent slipping, per the listing.
360-degree rotation for portrait or landscape viewing.
Comes with three silicone bands in different colors.
Cons
No brand or model name, and handlebar diameter range is not specified.
No quick-release; the phone is held only by grips and a band.
Best for: Riders who want a cheap, simple handlebar phone holder for navigation.
Skip it if you need a locking quick-release mount or have a very large phone in a thick case.
Measure your handlebar diameter first, because the clamp range rules out more mounts than phone size does. The Lamicall BM02 and BP07 cover 15-40 mm, the widest range here. The JOYROOM stops at 1.34 in, the Roam at 1.25 in and the TruActive at 1.26 in (32 mm), while the unbranded holder gives no range at all. E-bike bars are often oversized near the stem and crowded with a display, throttle and brake levers, so measure the exact spot where the mount will go, not just the grip area. A soft tape or caliper is enough.
Phone and case size
Check your phone's size with its case on, since thickness is where most mounts fail. The two Lamicall mounts take up to 0.59 in thick, the TruActive up to 18 mm and the JOYROOM up to 0.71 in. For length, the JOYROOM, Roam and TruActive go to 7 in, the Lamicall pair to 6.8 in. Lamicall warns that Galaxy S25 Ultra and S24 Ultra phones in a case may not fit the BP07. Measure your phone rather than trusting the model name alone.
Locking and release
Pick a mount with a lock if you ride fast or on rough pavement. The Lamicall BM02 locks with a red switch, the BP07 with a metal lock, and the JOYROOM adds a second lock switch to its auto-lock arms. The Roam net, TruActive grips and unbranded holder rely on tension alone. For release speed, the JOYROOM is the quickest, opening with a two-side press. A net or band mount takes longer, because you stretch it over the phone each time you set off and again whenever you park.
Rotation and viewing angle
Choose a ball joint if you want to fine-tune the angle around your e-bike's display. The BP07, JOYROOM and Roam all use a 360-degree ball joint or socket, the TruActive a ball joint for any angle, and the unbranded holder rotates 360 degrees. The BM02 switches between vertical and horizontal only. On an e-bike the phone often sits next to a handlebar display, so being able to tilt it slightly away from glare and from the display helps. Check that the clamp does not cover your camera if you use it on rides.
Vibration and rain
Expect only partial protection from vibration and none from rain. The Roam listing says its ball socket dampens vibration, the TruActive has an anti-vibration pad, and the BP07 listing says plainly it has no vibration damper. None of these mounts includes a waterproof cover, and the Roam net leaves the phone fully exposed. If you commute in wet weather, keep a waterproof case on the phone or take it off in heavy rain. Faster e-bike speeds mean more road buzz reaches the phone than on a regular bike.
Skip it if…
your phone in its case is thicker than the mount allows, which is 0.59 in on both Lamicall models.
your handlebar is oversized and you were looking at the JOYROOM, Roam or TruActive clamps.
you ride in the rain often and want a mount that covers the phone.
you own a Galaxy S25 Ultra or S24 Ultra in a case and planned on the Lamicall BP07.
you need to confirm bar fit before buying, which the unbranded holder does not let you do.
FAQ
What is the best bike phone mount for an e-bike?
For most riders, the Lamicall BM02 is the best bike phone mount on this page. It locks the clip with a switch, fits phones from 4.7 to 6.8 in and handlebars from 15 to 40 mm, and has a 4.6 rating from 69,002 reviews. If your phone is larger or in a thick case, look at the JOYROOM, which takes up to 7 in and 0.71 in thick.
Will a bike phone mount fit my e-bike handlebar?
It will if the clamp range covers your bar diameter, so measure before you buy. The Lamicall BM02 and BP07 fit 15-40 mm bars, the JOYROOM 0.7 to 1.34 in, the Roam 7/8 to 1.25 in and the TruActive 15-32 mm. The unbranded holder lists no range. Measure at the spot where the mount will sit, since bars often widen near the stem.
Can a phone fall out of a bike mount?
It can if the mount is loose or the phone is too big, which is why a locking clip helps. The Lamicall BM02 and BP07 lock the clamp, and the JOYROOM adds a second switch to its auto-lock arms. Net and band holders such as the Roam rely on tension. Recheck the clamp after your first rides and stay within the stated phone size.
Is a bike phone mount safe for my phone camera?
The listings do not promise anything about cameras, so treat this as a risk you cannot rule out. None of these six mounts gives a vibration figure. The Roam says its ball socket dampens vibration, the TruActive has an anti-vibration pad, and the Lamicall BP07 listing states it has no damper. If you are worried, remove the phone for long rides on rough roads.
Do bike phone mounts block the camera?
Some do. The brand tables for the Lamicall BP07 and the JOYROOM both indicate the clamp can block the camera. The Roam net leaves the camera, buttons and charging port open. If you film rides or scan codes with the phone on the bars, compare your camera position with the photos on the product page before ordering.
I
Ilias, eBike Compas
Models are picked from the product listings on Amazon.com, recorded and dated. Missing data is flagged instead of guessed, and no hands-on test is described unless it actually happened. Our method